Download Zebra 170 XiIII Plus PowerPoint Presentation

Login   OR  Register

Share page


Home / General & Others / General & Others Presentations / Zebra 170 XiIII Plus PowerPoint Presentation

Zebra 170 XiIII Plus PowerPoint Presentation

worldwideweb By : worldwideweb

On : Jun 04, 2015

In : General & Others

Embed :

Login / Signup - with account for

  • → Make favorite
  • → Flag as inappropriate
  • → Download Presentation
  • → Share Presentation
  • Slide 1 - 1 Zebra 170 XiIII Plus Removing and Installing Printhead Calibrating Head Resistance Print Quality Adjustments
  • Slide 2 - 2 Removing Printhead Turn the power switch off and disconnect both the power cord and printer communications cable. Open Cover. Open Printhead Lever. *Make sure you are appropriately grounded using proper anti-static procedures. Removing the printhead Printhead Lever
  • Slide 3 - 3 Remove media and ribbon (if applicable). Unscrew Printhead mounting screw with flat-head screwdriver.
  • Slide 4 - 4 1. Holding the Printhead, carefully disconnect the left Printhead cable (gray), then the right Printhead cable (white) from the back of the Printhead. 2. Remove the Printhead. Left Printhead Connector Right Printhead Connector
  • Slide 5 - 5 Installing the Printhead Turn the power switch off and disconnect both the power cord and the printer communications cable. Open the side cover. Make sure to note the new Printhead resistance before installing in the printer. Resistance needs to be calibrated before test printing labels. See calibration instructions.
  • Slide 6 - 6 Carefully position the new Printhead under the Printhead mounting bracket and connect both Printhead cables into the appropriate ports. Strip Plate Left Printhead connector Right Printhead Connector
  • Slide 7 - 7 Position the alignment slots in the new Printhead with the alignment posts on the bottom of the mounting bracket. You should hear a “clicking sound” which signifies that the Printhead is securely in place. Tuck the Printhead cables behind the Printhead. Alignment slots In Printhead Alignment Posts
  • Slide 8 - 8 Print line Alcohol swab Clean the Printhead using an alcohol swab, removing dirt or oil that may have been deposited during installation.
  • Slide 9 - 9 Reinstall media and ribbon (if applicable).
  • Slide 10 - 10 Lower the Printhead Assembly. Close the Printhead lever and check for proper alignment. Close the side cover. Connect the power cord and printer communications cable. Turn power on. If the print line is not parallel with the platen roller, check that the Printhead Assembly guides fit snug into the Printhead slots.
  • Slide 11 - 11 Printhead Resistance Calibration Printhead Resistance Calibration
  • Slide 12 - 12 On the LCD, press setup/exit. Pressing the left arrow button (Previous), scroll left until LCD displays HEAD RESISTOR. Press left or right back oval key to decrease or increase ohm value.
  • Slide 13 - 13 LCD will display ENTER PASSWORD. The default password is 1234.
  • Slide 14 - 14 Change ohm value to match the new Printhead. The right black oval key increases the digit, while the left black oval key moves cursor. Check that the new ohm value matches the new Printhead. Press SEUP/EXIT. The LCD displays SAVE CHANGES PERMANENT. Press NEXT/SAVE button to save. Resistance
  • Slide 15 - 15 Printhead Position Adjustment Printhead Position Adjustment If print is lighter toward one side of the label and Printhead has been correctly installed, perform the Printhead Position Adjustment. Loosen the four top screws, found at the rear of the Printhead Assembly (do not remove). Top screws
  • Slide 16 - 16 1. Adjust the two gold hex nuts found at the rear of the Printhead Assembly (as viewed from the rear of the Printer). Adjusting the gold hex nuts clockwise will move the Printhead toward the back. Making 1/8 turns will have a noticeable affect in the print. Gold hex nut 2. Adjust the hex nut on the same side as the lighter print. Adjust in one direction, printing a test label after each adjustment. If print begins to darken, continue until desired darkness is achieved. If print becomes lighter, adjust the hex nut the opposite direction until maximum print darkness is reached.
  • Slide 17 - 17 Toggle Position Adjustment Toggle Position Adjustment Loosen locking nuts so the toggles slide freely. Position the two toggles so they distribute even pressure across entire label. Locking nut Upper knurled nut Adjusting nut
  • Slide 18 - 18 Wear Plate Adjustment Wear Plate Adjustment Perform this adjustment to help achieve even pressure. Run several test labels at 2 ips. During label testing, use the LCD panel to lower the darkness setting until the labels print gray instead of black. Use a 7/64 hex wrench to loosen two hex screws attached to wear plate. Wear Plate Hex nuts Silver Adjustment Knob
  • Slide 19 - 19 Wear Plate Hex nuts Silver Adjustment Knob For even pressure across width of label, adjust the Silver Adjustment Knob with your hand or with a 7/16 wrench. Turning the Silver Adjustment Knob clockwise will increase pressure on the left side of label (as viewed from front of printer). Adjusting it counter-clockwise will increase pressure on right side of label. When gray print is even across label, tighten the two hex nuts to secure wear plate in place. On the LCD, increase darkness setting to achieve desired print quality.
  • Slide 20 - 20 Printhead Pressure Adjustment Printhead Pressure Adjustment Selecting 2 ips from the printer or the label software, print several test labels. During the test printing, use the LCD panel to lower the darkness setting until the labels print gray instead of black.
  • Slide 21 - 21 On the toggle assemblies, loosen the Upper knurled nuts found above the adjusting nuts. Looking down at the printer, use the adjusting nuts to increase (clockwise) or decrease (counter-clockwise) pressure until the darkness is uniform across label. Once uniformity is achieved, adjust the darkness level on the LCD until printing is clear. Tighten the Upper knurled nuts against the Adjusting nuts. Too much pressure applied to the toggles will shorten the life of the Printhead. Choose the lowest pressure that produces the desired print quality, which will maximize Printhead life.
  • Slide 22 - 22 Zebra is a registered trademark of ZIH Corp. All other trademarks are the property of their respective owners. (*) Contents Subject to Change Without Notice. Doc. No. Z170XiIII-Instructions
Bowling Free PowerPoint Template


Views : 749

Cigarettes Free PowerPoint Template


Views : 867

Photography Free PowerPoint Template


Views : 484

Female Mosquito Free PowerPoint Template

Female Mosquito

Views : 531

Drugs Medicine Free PowerPoint Template

Drugs Medicine

Views : 1098

Swans Free PowerPoint Template


Views : 473

Bird Free PowerPoint Template


Views : 345

Social Media Words Free PowerPoint Template

Social Media Words

Views : 460

Ocean Free PowerPoint Template


Views : 387

Interior Free PowerPoint Template


Views : 560

Time Management Free PowerPoint Template

Time Management

Views : 553

Good Friday Free PowerPoint Template

Good Friday

Views : 966

Woman Meditation Free PowerPoint Template

Woman Meditation

Views : 543

Traffic Lights Free PowerPoint Template

Traffic Lights

Views : 634

Saving Money Free PowerPoint Template

Saving Money

Views : 890

Diet Free PowerPoint Template


Views : 502

Nature Abstract Free PowerPoint Template

Nature Abstract

Views : 560

Cloud Computing Technology Free PowerPoint Template

Cloud Computing Technology

Views : 2997

Autumn Free PowerPoint Template


Views : 607

Law Rules Free PowerPoint Template

Law Rules

Views : 1919

Description : Download Zebra 170 XiIII Plus PowerPoint Presentation Slides

Tags : Zebra 170 XiIII Plus

Shortcode : Get Shareable link